I haven’t yet, but I’ll probably just do a file level swap, which is easy enough to do
could also just add it to config file, if you use the above it can automate this for you

some interesting benchmarks, the first one is an image on a raid 10 f2 configuration rated to around 200r/100w MB/sec, but the results are probably due to file caching
The other two are phycial md arrays, raid 10 rated to 100r/100w MB/sec

ron@server:~$ sudo hdparm -t /dev/xvda

/dev/xvda:
Timing buffered disk reads: 1088 MB in 3.00 seconds = 362.36 MB/sec
ron@server:~$ sudo hdparm -t /dev/xvdb

/dev/xvdb:
Timing buffered disk reads: 368 MB in 3.01 seconds = 122.41 MB/sec
ron@server:~$ sudo hdparm -t /dev/xvdc

/dev/xvdc:
Timing buffered disk reads: 336 MB in 3.02 seconds = 111.27 MB/sec

Some good tools to deal with this are defraggler and smart defrag. defraggler is great at file level fragmentation but that about where it ends. smart defrag however has alot of the feature of premium products such as boot time defrag (to defrag system files that are normally locked during normal operation, reg hives, mft, system dll’s). It also offer contiuous defragmentation which runs defrags when system usage is below a specified level. Both these products offer the ability to easily schedule defrags to run at off hours.

Server fragmentation can slow down an entire network so its always a good idea to stay on top of these, both of these program will work, would not use the auto feature on a server though, and be sure to put in exceptions for things like database files and database backup files. Since these are going to always be fragmented. But if you follow best practices with disk fragmenation you can minimize the amount that they will fragment. Both of these will allow single file defrag and files this comes in handy for are outlook datafiles and sql database files, you need to close outlook or sql to run these to remove the file locks, and especially with sql you need to make sure their is enough continous free space for the defrag to have any effect. So running regular defrags before attemping sql defrag, or exchange defrag (see microsoft kb article not recommened to use these tools on stores) will provide better results.

For those interested, you can also check fragmentation on linux system, and if your so inclined recompile your kernel and compile the defrag tools for ext4. Or just wait a few more years for these tools to make it into mainstream releases.

for software raids

sudo e2fsck -nfv /dev/md0 (number of the md device)

regular scsi disk (most kern now see sata as scsi)

sudo e2fsck -nfv /dev/sda1 (letter of device and number of partition)

system that see your disk as ide

sudo e2fsck -nfv /dev/hda1 (letter of device and number of partition)

http://www.iobit.com/iobitsmartdefrag.html

http://www.piriform.com/defraggler

Server supported defrag solutions that will provide continuous and idle defrag and further fragmentation protection

http://www.iobit.com/iobitsmartdefrag.html

http://www.diskeeper.com/business/diskeeper/server/default.aspx

The only exception to this rule is SSD you do not defrag SSD and in system with SSD such as 2008 R2 or windows 7 you should disable the defrag service and manually defrag any conventional disk.

NTFS is not much better off at dealing with this then FAT32, the real benifit with NTFS is longer file names, larger files, file system journaling

Virtualization is also not immune to fragmentation, and when hosting vm’s on windows, make sure you always allocate all space at the creation of a virtual disk, then check fragmentation level of the allocated disk prior to first boot, if you allocate at once, and insure fragmentation of the file is within reason you won’t have to worry so much about dual level fragmentation between the host and guest os. You will however still need to consider guest level fragmentation of your virtual machines.

With Pagefile fragmentation, you can avoid this all together by calculating a safe size for your pagefile in advance, which is usually recommended to be 1.5x phycial memory, setting it to allocate the entire size from the start will ensure it does scrink and grow  and risk fragmentation.

Keeping up with file level fragmentation can also reduce the chances of registry hives becoming heavily fragmented, their is however a special tool for checking these hive files and boot time defragging them if needed.

http://technet.microsoft.com/en-us/sysinternals/bb897426

Well I had to turn in my old modem before they would activate the new one but other then that it was pretty painless. However new modem has gigabit eithernet port on it and can scale to 160mbps, old one was the crap they gave out, looked it up and it was a low end DOCSIS 2.0 I was getting burst of up to 24mbps but averaged around 15, with 2-3mbps up. Hooked up the new one, did a quick speed test, 50mpbs down 2 up, tested it 10 different times 10 different sites, on each one it maxed out what ever their limit was, so i’m not entirely sure how fast its capable of, but its measuring at 50mbps. Pretty freaking impressive for a one time purchase, sure didn’t upgrade my plan so they could what, give my packets higher priority, i don’t exact live someone where bandwidth is in high demand, never had slow downs, sounds like marketing BS to me.

But still, if you have comcast, you can go to their site and check your area for DOCSIS 3.0, we got it here, won’t say where, but the only thing is, the down stream is not bonded, its just a single connection, upstream is a quad connection so its technically capable of 160mbps, when I get that 20Mbps download i’ll be sure to post a screen shot.

Comcast Docsis 3.0

Surfboard Extreme

If you decide to upgrade with this you can reach the status page via 192.168.100.1 as long as you don’t have a route rule for that subnet
Also the lights are speed sensitive, the lights are green for old school or nonbonded and blue for bonded, the ethernet port reflect gigabit-ethernet blue, or green for fast-ethernet

I’m sure theirs a way to make dns work on a peer-to-peer network more effectively, maybe some reg edits here and their but on standard windows pc, which you can usualy assume, WINS, is going to be the best bet.

First set your samba server to be the master wins server, these options have worked best for me
#WINS SHIT
#Just cause i like a sure thing
os level = 99
# well this is needed
wins support = yes
name resolve order = wins lmhosts hosts bcast
domain master = yes
preferred master = yes
#Because I auth to a local ddns server with my dhdns proxy = yescp server
#the following helps with peer-to-peer traffic
dns proxy = yes
The above pretty much guarantees your be the WINS master server.

Now onto dhcp, because I just don’t like dicking with wins
option netbios-name-servers SAMBASERVERIP;
option netbios-node-type 8;

This will help increase the access time of your windows clients to your samba server, pretty much instant. \\hostname and bam, also speeds up windows – windows, network neighhood(network i guess is what its called now)

To increase the speed on the samba server even more I increase the buffer size and set some socket options
socket options = TCP_NODELAY SO_RCVBUF=16384 SO_SNDBUF=16384

Your want to do a dump of any db’s your hosting, i could be wrong here, but in my experience when switching architecture you can’t just grab the db’s out of var and throw them on the new system they have to be restored, again ymmv, but just incase do a dump.

install the 64 bit version, then before rebooting df should tell you where your new file system is mounted, chroot into it, reinstall your applications, a good start would be to rerun
dpkg --get-selections > install2.txt
and do a
diff install2.txt install.txt
once you have that done reboot into your now 64 bit system
run updates
Again ymmv, but i’ve had pretty good luck with this method going from solaris (was quiet a bit more envolved, had to convert formats on pretty much every config) to openbsd, then switch over to ubuntu, now getting ready to switch over to ubuntu 64, need more memory and gotta make the jump back to 64.
first thing restore /etc, now careful here, if your just doing 32 -> 64, should be ok, theirs shouldn’t be any major format changes to config files, and more then likely your not going to want to change much in etc from your old system, this will also pull in all your old users and password
then restore /home /root and possible /opt /var/www /var/mail and depending on what else you were running and were you stored data their could be more
your want to check and make sure your fstab is setup correctly if you formatted your parts your need to update the uuid, and you can find this in dev, google it
a reboot and you should be back where you left off, only 64-bit, theirs probably going to be more to do to make sure your stable, but a quick glance at dmesg and syslog will probably point out any thing you missed, and if you have to can always restore to a dif disk and boot to that to figure out what your missing.

Workstation, just run gparted, offload /home to a dif partition and then reinstall, before restart, ctl+alt+f1, df to see where your mounted, chroot in,
mv /home /home.bak
mkdir /home
vi /etc/fstab
put in mount point for /home partition
you can also use the
dpkg --get-selections
prior to install and get an idea what will need to be reinstalled, but all your personal settings will come over.

From the same people that made a purple workstation, so go figure, they’d make a video to go with said purple workstation.

Now this didn’t seem like an option to me cause I’ve already added usb and GbE to the PCI bus and already have an excess of FC-AL drives I got off ebay for next to nothing (guessing they were someones spares left over after retiring a server)

So I tried again to install debian during install it ask for EDIT THIS q22xxx.bin firmware. So I googled it. Nothing. So I decided to dig a little dipper. EDIT DETAILS

lspci
and
lsmod
Gave me enough information to then google and find that EDIT qlogic doesn’t do opensource firmware so firmware was proprietary. Also found that in dmesg it gives an ftp site to download said firmware. But better yet apt-cache search EDIT qlogic yields that in the non-free repository this be the firmware. So I download it, setup networking in the install, pull the extracted firmware from my main system over http and put it in /lib/firmware rerun the scan and good to go.

I ended up doing an install. Setting up a degraded raid on my second drive, migrating the install then initalizing the raid on first boot.

Didn’t want to wait for the intial raid to setup so I took a short cut.

Sound was also a bitch to get working tried to manually add the kernel module with modprobe then rerun alsa scan, still didn’t take then ran EDIT alsaconf and was good to go.

Ended up installing the debian desktop under tasksel then switched it to xfce4 and xdm.